Category: News

  1. Hydronic Systems Information

    Underfloor heating systems can also called Hydronic systems, especially in the United States. Most underfloor heating systems would use either PEX, PEX/AL/PEX, PB or PERT pipe for the wet underfloor heating pipework. Copper pipework are not used for modern wet underfloor heating systems as the copper would react with the screed and would result in […]

    Read more /

  2. Underfloor Heating Manifold Control Pack Instructions

    The underfloor heating manifold control pack provides temperature controlled mixed water to an underfloor heating system with a heat output up to 14 kW.  Our pump station is made by Reliance Water Controls in the UK – www.rwc.co.uk. The specification for the underfloor heating mixer pack is; Maximum pressure: 10 bar Maximum temperature: 90 degree […]

    Read more /

  3. Wet underfloor heating review

    All underfloor heating insulation requirements must comply to the latest building regulations. Normal screed can be used for underfloor heating systems.  No further additives are required. Anhydride screed can be 50 mm only.  It is very important to use a vapour barrier when using liquid screed for wet underfloor heating. The best floor finish for […]

    Read more /

  4. Underfloor Heating Wiring Centre Heatmiser UH3

    The Heatmiser underfloor heating wiring centre is one of the best on the market in the UK.  It comes with a 5 Amp fuse time delay. Mains supply will connect from a fused spur into the underfloor heating wiring centre.  There is also a relay for switching the boiler/two port valve on.  The wet underfloor […]

    Read more /

  5. Actuator for Underfloor Heating

    Our underfloor heating actuator from Henco in Belgium is made to the highest quality possible. It is an ON/OFF electrical head and the actuator is fitted on the underfloor heating return manifold. The specification for our underfloor heating Henco actuator is; Type of load controlled by the extrenal circuit – 700 mA. Type of action […]

    Read more /

  6. Underfloor Heating Manifolds

    Our underfloor heating manifolds are made in Germany by Watts/Dumser to the highest quality possible.  The underfloor heating brackets are mounted to adjustable C-rails.  The wet underfloor heating manifolds are supplied with a ball valve set and a filling set. The underfloor heating manifolds are each fitted with a 1″ male thread for fixing the […]

    Read more /

  7. Henco Underfloor Heating Pipe

    At Underfloor Heating Systems Limited we use Henco mulitlayer pipes for our underfloor heating system.  See website www.henco.be. The wet underfloor heating system must be 100 % oxygen diffusion tight, which is guaranteed by using Henco multilayer pipe.  The aluminium layer eliminates any corrosion risk in the underfloor heating system. The aluminium layer will also […]

    Read more /

  8. Underfloor Heating Pipe and Engineered Boards

    Our underfloor heating pipework is from HENCO in Belgium.  It is approved for 10 bar pressure and 95 degree C water temperature, one of the best approvals you can have for an underfloor heating pipe.  The aluminium layer makes sure that the underfloor heating pipe is 100 % oxygen diffusion tight. Our HENCO underfloor heating […]

    Read more /

  9. Underfloor Heating Single Zone (Single Room)

    One of our many available products is the Single Room pack, ideal for extensions and conservatories. It can work as part of the radiator system or it can have a separate feed from the heating source (which is the recommended practice).  Any wet underfloor heating system will work best as a separate system with S-Plan […]

    Read more /

  10. Wet Underfloor Heating

    Wet underfloor heating is very energy efficient.  Having underfloor heating installed will reduce your energy bills and keep your feet warm. The heat will only be circulated in the rooms where it is required.  Each room will have it’s own room temperature control.  No ugly radiators to be fitted on the wall, you will have […]

    Read more /