News
Underfloor Heating Cost 2026: The Complete UK Price Guide

This guide is for UK homeowners planning a renovation, extension, or heat pump upgrade who need a realistic budget for underfloor heating. Prices reflect current UK market data and Ofgem’s energy price cap as of July 2026; get a property-specific quote before committing, since costs vary by floor construction, insulation, and location.
What Does Underfloor Heating Cost in 2026?
Underfloor heating cost is one of the first questions anyone renovating, extending, or switching to a heat pump has to answer, and it isn’t a single number. In 2026, UK underfloor heating cost ranges from around £40 per m² for a simple electric retrofit up to £190 per m² for a complex wet system retrofit, with most whole-house wet installations landing between £6,000 and £13,000.
This guide breaks that down by system type, room size, and region, then works through the underfloor heating cost vs radiators comparison in detail, covering both installation and running costs. You’ll also find current 2026 energy price cap figures, grant information, and a practical budgeting checklist.
Key takeaways:
- Electric underfloor heating costs £40 to £120 per m² installed; wet (water) systems cost £70 to £190 per m².
- A typical 3 bed house (80 to 120m²) with whole-house wet underfloor heating costs £6,000 to £13,000 supplied and fitted.
- Underfloor heating almost always costs more to install than radiators but 25 to 30% less to run, rising to around 40% less when paired with a heat pump.
- Running cost figures in this guide use Ofgem’s price cap for 1 July to 30 September 2026: 26.11p per kWh for electricity and 7.33p per kWh for gas.
Contents
- Underfloor Heating Cost Per m²
- Cost by Room and Property Size
- Cost by UK Region
- What Affects the Cost of Underfloor Heating
- Underfloor Heating Running Costs in 2026
- Underfloor Heating Cost vs Radiators
- Hidden and Additional Costs
- How to Save Money on Underfloor Heating
- Frequently Asked Questions
Underfloor Heating Cost Per m²
Installers almost always quote underfloor heating cost per m², since it’s the fairest way to compare a small bathroom against a whole-house project. The number you get depends first on system type (electric or wet) and second on whether it’s going into a new build or being retrofitted.
| System type | Cost per m² (supply and install) | Best suited to |
|---|---|---|
| Electric underfloor heating | £40 to £120 | Bathrooms, ensuites, single-room retrofits |
| Wet (water) underfloor heating | £70 to £190 | Whole-house heating, new builds, heat pump systems |
Electric Underfloor Heating Cost
Electric systems use heating mats or loose cables beneath the floor, controlled by a thermostat, and sit on top of insulation boards. They typically cost £40 to £120 per m² installed, averaging around £85 per m², and are quicker to fit than wet systems since there’s no pipework or manifold involved. Smaller or awkwardly shaped rooms, like a small downstairs toilet, tend to sit at the higher end of that range, because cutting and fitting the mat takes proportionally more labour regardless of room size.
Wet (Water) Underfloor Heating Cost
Wet systems circulate warm water from a boiler or heat pump through a network of pipes connected to a manifold. Supply-and-install pricing typically runs £70 to £120 per m² in a new build or straightforward renovation, rising to £90 to £190 per m² in a retrofit where the floor needs lifting, levelling, or extra insulation. Supply-only kits, if you’re managing installation separately, generally cost £30 to £55 per m².
New Build vs Retrofit
Installing underfloor heating while a floor is still open, before screed or finishes go down, is consistently the cheapest route, which is why new-build and major-renovation pricing sits at the lower end of both ranges above. Retrofitting into a finished property adds cost for lifting existing flooring, levelling the subfloor, upgrading insulation, and making good skirting and door thresholds afterwards. Whole-property retrofit projects typically total £3,000 to £13,000 depending on how much of the home is being converted.
Cost by Room and Property Size
| Room or project | Approx. size | Electric UFH cost | Wet UFH cost |
|---|---|---|---|
| Small bathroom or ensuite | 4m² | £240 to £480 | £2,000 to £2,500* |
| Kitchen | 20m² | £800 to £2,400 | £1,400 to £3,000 |
| Whole ground floor (new build) | 60m² | Not typically used at this scale | £4,200 to £7,200 |
| Whole 3 bed house | 80 to 120m² | Not typically used at this scale | £6,000 to £13,000 |
*Small single-zone wet systems carry a higher effective cost per m² because the manifold, pump, and controls are a largely fixed cost whatever the floor area, so a tiny bathroom rarely reflects the headline £70 to £190 per m² rate. Electric systems are rarely used to heat a whole floor or house, since running costs at that scale become expensive; wet systems are the standard choice for whole-property heating.
Because of that fixed-cost effect, a popular compromise in retrofits is a hybrid layout: wet or electric underfloor heating in the kitchen and bathrooms where it’s most noticeable underfoot, with radiators kept in the rest of the house. This avoids the cost of extending pipework and manifolds throughout a whole property while still getting underfloor heating where it adds the most comfort.
Cost by UK Region
| Region | Wet UFH cost per m² | Notes |
|---|---|---|
| London and South East | £110 to £120 | Highest labour rates and access costs |
| Manchester and North West | £90 to £110 | Strong installer availability |
| Birmingham, Midlands and Northern England | £70 to £90 | Generally the lower end of the national range |
| Edinburgh and Scotland | £85 to £130 | Wide range, driven by older stone-built properties |
Labour rates for plumbers and heating engineers generally run £40 to £70 an hour, and that regional gap, alongside travel time, parking, and access in denser cities, is the main driver of the price difference. Rural or historic properties can push costs above the regional average regardless of location, simply because of the extra care needed around older floors and finishes.
What Affects the Cost of Underfloor Heating
- System type: electric costs less to install but more to run; wet is the reverse.
- Floor area: larger areas lower the cost per m²; small rooms cost more per m² due to fixed setup costs.
- New build vs retrofit: retrofitting typically adds 20 to 50% to the per m² price.
- Floor construction: suspended timber floors typically cost 15 to 25% more to convert than solid concrete or screed floors.
- Insulation: adding insulation increases the upfront bill but reduces the flow temperature needed, which lowers running costs.
- Controls: smart thermostats and room-by-room zoning add £200 to £800 but improve comfort and efficiency.
- Heat source capacity: a wet system may need a boiler upgrade (around £2,000) if the existing one can’t support extra heating zones.
- Location: labour rates and access, as shown in the regional table above.
Underfloor Heating Running Costs in 2026
Running cost figures below use Ofgem’s price cap for 1 July to 30 September 2026, which sets the average Direct Debit rate at 26.11p per kWh for electricity and 7.33p per kWh for gas, with daily standing charges of 57.19p and 29.04p. Fixed or dedicated heat pump tariffs can bring the electricity rate down further, so treat these as a ceiling rather than the only option.
Wet underfloor heating: a well-insulated 3 bed home with whole-house wet underfloor heating commonly sees a heating cost in the £290 to £500 a year range. That figure assumes reasonable insulation and a properly zoned, balanced system. Industry estimates put wet underfloor heating at 25 to 30% cheaper to run than an equivalent radiator system on the same fuel, rising to around 40% cheaper when paired with a heat pump. That gap doesn’t come from the underfloor pipes themselves using less energy; it comes from the lower flow temperature (35 to 45°C, against 60 to 80°C for radiators) letting a condensing boiler or heat pump run in its efficient range far more of the time.
Electric underfloor heating: because electricity is priced roughly 3.5 times higher per kWh than gas under the current cap, electric systems cost considerably more to run over large areas or long hours, which is why they suit small, occasionally-used rooms better than whole-home heating. As a worked example, a 4m² bathroom with a typical 150W/m² output, run for 2 hours a day, uses around 1.2kWh a day. At 26.11p per kWh that’s roughly 31p a day, or about £115 a year, on top of the standing charge.
Underfloor Heating Cost vs Radiators
For most homeowners, the real question isn’t just what underfloor heating costs on its own, it’s the underfloor heating cost vs radiators comparison: which one is the better investment for a given room or budget.
Installation Cost
Radiators are the cheaper starting point in almost every case. A single radiator replacement averages around £200, typically £150 to £350 including labour and valves, and a full house of 5 to 8 radiators usually costs £1,200 to £3,500. Wet underfloor heating at £70 to £190 per m² is almost always more expensive to install across a whole property, though a small electric UFH zone can occasionally undercut fitting a single new radiator in the same room.
Running Cost
Running cost comparisons vary a lot between sources because they depend heavily on property size and insulation, so treat any single figure as a starting point rather than a quote. One commonly cited whole-home example puts a gas-fuelled radiator system at around £1,900 a year, while a well-insulated home with wet underfloor heating is often quoted nearer £290 to £500 a year for the heating itself. Much of that gap reflects insulation standards rather than the emitter type alone, but the consistent, cross-source finding is that underfloor heating saves 25 to 30% against radiators on the same fuel, and up to 40% against radiators on a heat pump.
With a Heat Pump
This is where the comparison matters most in 2026. Radiators typically need water heated to 60 to 80°C to perform well, while heat pumps run most efficiently between 35 and 55°C. Standard radiators can still work with a heat pump, but they often need to be oversized to compensate, adding cost and taking up more wall space. Wet underfloor heating already operates at 35 to 45°C (and is capped at a maximum 55°C flow temperature under 2025’s Part L building regulations), making it a natural match for a heat pump, which is why most new heat pump installations pair the two, at least on the ground floor.
| Wet underfloor heating | Radiators | |
|---|---|---|
| Typical installation cost | £70 to £190 per m² | £150 to £350 per radiator |
| Typical running cost | £290 to £500/year (well-insulated home) | Often £1,900+/year on a comparable basis |
| Ideal flow temperature | 35 to 45°C | 60 to 80°C |
| Heat pump compatibility | Excellent | Good, may need oversized radiators |
| Best suited to | New builds, major renovations, heat pump installs | Retrofits, quick swaps, tighter budgets |
Hidden and Additional Costs
Beyond the headline per m² price, budget for:
- Floor levelling or self-levelling compound if the existing subfloor isn’t flat
- Extra insulation boards, especially in retrofits and ground floors
- A boiler upgrade or replacement if the current one can’t support extra zones (around £2,000)
- Manifold, pump, and zone valves for wet systems
- Smart thermostats or multi-zone controls (£200 to £800)
- A compatible floor finish; tile generally performs best, while thick carpet needs extra consideration
- Door, skirting, and threshold adjustments if the retrofit changes floor height
- Part P electrical certification for electric systems fitted in bathrooms and other wet areas
- VAT: confirm with your installer whether standard 20%, reduced, or zero rate applies to your job
How to Save Money on Underfloor Heating
- Get at least three quotes. Per m² pricing for comparable jobs varies significantly between installers and regions.
- Time it with a new build or major renovation rather than a standalone retrofit, since new-build pricing sits at the lower end of the per m² range.
- Consider a hybrid layout: underfloor heating in the kitchen and bathrooms, radiators elsewhere, instead of converting a whole house.
- Bundle it with a heat pump installation. Qualifying energy-saving installations currently benefit from 0% VAT until 31 March 2027 (reverting to 5% after), and underfloor heating fitted as ancillary work within the same heat pump contract can sometimes fall under that relief, though a standalone underfloor heating project doesn’t automatically qualify. Check with your installer or an accountant before assuming it applies.
- Use the Boiler Upgrade Scheme if you’re switching from a fossil fuel boiler. It currently offers £7,500 towards an air or ground source heat pump in England and Wales (£9,000 for eligible oil or LPG homes between 21 July 2026 and 31 March 2027), which can offset the combined cost of a heat pump and any underfloor heating fitted alongside it.
- Zone your controls. Heating only the rooms you use, when you use them, is one of the biggest levers on running cost regardless of system type.
Frequently Asked Questions
How much does underfloor heating cost per m² in the UK?
Electric underfloor heating costs £40 to £120 per m² installed in 2026, and wet (water) underfloor heating costs £70 to £190 per m². New builds sit at the lower end of each range; retrofits, especially those needing floor levelling or extra insulation, sit at the higher end.
Is underfloor heating cheaper than radiators to run?
Usually, yes. Wet underfloor heating typically costs 25 to 30% less to run than radiators on the same fuel, rising to around 40% less when paired with a heat pump, because it operates efficiently at much lower water temperatures than radiators need.
Is underfloor heating cheaper than radiators to install?
No, not usually. Radiators cost £150 to £350 per radiator to install on average, while wet underfloor heating costs £70 to £190 per m². For a like-for-like whole-house project, radiators are almost always the cheaper upfront option; underfloor heating earns its cost back through lower running costs over time.
How much does it cost to retrofit underfloor heating into an existing house?
Retrofitting a whole property typically costs £3,000 to £13,000, depending on floor area, floor construction, and how much levelling or insulation work is required. Retrofits generally cost 20 to 50% more per m² than fitting underfloor heating during a new build.
Does underfloor heating work with a heat pump?
Yes, and it’s usually the better pairing of the two. Wet underfloor heating runs at 35 to 45°C, close to a heat pump’s most efficient range, while standard radiators often need to be oversized to perform well at a heat pump’s lower water temperatures.
Can I get a grant or VAT relief for underfloor heating?
Underfloor heating isn’t directly grant-funded on its own, but it can benefit indirectly. If it’s installed alongside a heat pump, the Boiler Upgrade Scheme’s £7,500 grant (or £9,000 for eligible oil and LPG homes from 21 July 2026) reduces the overall project cost, and it may qualify for 0% VAT as ancillary work under the current energy-saving materials relief, in place until 31 March 2027.
Conclusion
Underfloor heating cost in the UK spans a wide range in 2026, from around £40 per m² for a small electric bathroom retrofit to £190 per m² for a complex wet system retrofit, with most whole-house wet installations landing between £6,000 and £13,000. It costs more to install than radiators in nearly every scenario, but the running cost savings, typically 25 to 30% and up to 40% with a heat pump, mean it often earns that difference back over the system’s working life, particularly in a well-insulated home.
If you’re weighing underfloor heating against radiators, the honest summary is that radiators remain the cheaper starting point, while underfloor heating is the stronger long-term investment, especially where a heat pump is part of the plan. Get quotes from a few MCS-certified or Gas Safe-registered installers for your specific property before committing: floor construction, insulation, and existing pipework will move your final number more than any average in this guide.
Sources: Ofgem energy price cap (July to September 2026), Checkatrade, MyJobQuote, Energy Saving Trust, GOV.UK Boiler Upgrade Scheme guidance, and HMRC VAT Notice 708/6.

